HHO gas generators, fuel cells and car kits can help increase gas mileage. As gasoline or petrol spirals out of control you may be looking at gas alternatives to help reduce costs of operating a vehicle. What if there was and HHO gas plans were available for a car or truck and worked with diesel fuel?

HHO gas has also been called browns gas or hydroxy and has been used for welding applications. HHO gas is one of the best methods to improve gas mileage. HHO generators are sometimes called hydrogen cells or hydrogen on demand but actually produce two gases; oxygen and hydrogen. What you should expect is less pollution from the exhaust of your vehicle.

HHO gas is produced from a process called electrolysis which converts water to hydrogen and oxygen. You probably have seen the HHO car on the news and used for welding but the point here is you get a lot of energy from water with this process and end up with a hybrid water car. You will be supplementing you petrol or gas which should result in increased mileage.

HHO gas should help you see savings of 15 – 40 % or in some cases more including possible increases in horse power and acceleration. Did you ever see this from you favorite gas supplement? You may find Free HHO plans but only the best plans should be used because they often have the detail and pictures you need to properly install the device under the hood of your car or truck.

An HHO generator or car kit is easy to build and should make a nice day or weekend project. A HHO car kit will easily fit under the hood of most cars or trucks and should only take a few hours to install. Once installed it only takes a few minutes of maintenance a month to check the water and catalyst.

It is not uncommon to see free HHO gas plans missing a few details. The best HHO generators plans will show you in detail and have a parts list with pictures and step by step instructions. Very little engine modifications are required. Avoid spending hundreds or thousands on a commercial HHO car kit do it for much less with a good set of plans.

» Read More...

SET UP

Use care when handling cylinders. A hoist or other equipment must be used for heavier items.
1. Place cylinder on test stand.
2. Install correct fittings into ports.
3. Attach hoses to ports.
4. Set relief valve to operating pressure of cylinder.

STANDARD TEST

Make sure that the relief valve is set for the appropriate level. Fill cylinder with oil by alternately introducing oil into the extend and retract ports. Inspect all parts of the cylinder for leaks or damage.

5. Fully extend rod.

6. Check extend length to print.

7. Wipe rod.

8. Inspect rod for scratches or other damage.

9. Fully retract.

10. Check retracted length to print.

11. Pressurize retract/rod end port to relief pressure and hold.

12. Check for leaks around rod seal, head seal, port welds.

PISTON BYPASS INSPECTION

This test is to determine whether oil is leaking past the piston seals. Such a leak would allow the cylinder to drift while in operation.

13. Check for bypass over piston.

1. Disconnect hose from extend/base port (while retract/rod port is still pressurized).
2. Check for oil flow from extend/base port (should be none).
3. Reconnect hose to extend/base port.

14. Fully extend and pressurize extend/base port to relief pressure and hold.

15. Check for leaks around base and port welds.

16. Check for bypass over piston.

1. Disconnect hose from retract/rod end port.
2. Check for oil flow from retract/rod end port (should be none).
3. Reconnect hose to retract/rod end port.

COMPLETE TEST

Clean up and send to paint booth.

17. Fully retract with air pressure only.

18. Remove hoses and fittings.

19. Turn cylinder over to drain excess oil.

20. Plug ports.

21. Stamp with inspector number when complete and satisfactory.

22. Complete test report.

» Read More...

The economy has everyone in a position to look for ways to save money. Well this is one time that you can save money by spending money. Go out and look at some 50cc scooters and after you spend that small upfront investment, you are going to be amazed at how much extra cash is in your bank account.


As the cost of gas goes up, filling that monster that you drive around in is costing you a small fortune. Figuring that the average car gets about 20-25 MPG, you could be filling up your tank as many as 3 or 4 times a week. At $50 or more a fill, it gets pretty pricey. Wouldn’t you rather fill up your ride once a week and only spend about $15 to do so? With a 50cc scooter, you are going to get anywhere from 80-100 MPG and that means a lot less money being spent at the pump.

How aggravated do you get when you cannot find a parking spot anywhere? Maybe it is a quick run to the store or you are just going over to a friend’s house. If you live in the city, you may be parking blocks away and possibly even have to pay for your spot. Do you realize how small of a space a 50cc scooter can fit into?

Another great thing about the 50cc scooter is how easy they are to weave in and out of traffic. You don’t have that luxury when you are driving around in your BMW. You just get to wait in that long line like everyone else and watch the minutes and hours tick away on your watch. Wouldn’t it be nice to get some of that time back?

While these are some of the reasons, there are plenty of other ones as well. Think about the lower insurance rate that you are going to have to pay and how about the time that you will save because of some of the things we mentioned above. Lose your frustrations and save a few bucks in the process by merely traveling around the city on a 50cc scooter.

» Read More...